Examensarbetet syftar till att jämföra nya alternativ till olika system för användning i laborationer i reglerteknikkurser för olika studentkategorier. Det skall utredas vilket av ett antal alternativ till mjukvaruplattformar som är bäst lämpat att användas vid reglerteknikundervisningen i ITN:s reglerlaboratorium vid Linköpings universitet. Tidigare laborationer i berörda kurser skall även modifieras så att dessa kan genomföras i de nya systemen.Examensarbetet resulterade i en rad modifierade laborationer och system att tillämpa i dessa. De nya systemen medför att all reglering sköts direkt från en dator istället för tidigare variant med externa apparater som programmeras. På så sätt kan större fokus läggas på regleringen i sig och inte de system som tillämpas för att utföra den..

This thesis work contains a litterature study about electrical motors in general and how PWM-patterns for brushless DC-motors can be made. A suitable method has been implemented as a simulation model in VHDL. A simulation model of a brushless DC-motor which describes the phasecurrents, torque and angular velocity has also been made. The motor model made simulations easier for the complete PWM-system. The design was synthesised and tested with a prototypeboard including a SPARTAN II FPGA.

Simulation means running a model of a system with suitable input and observing the corresponding output. Real-time environment simulation is a special kind of simulation used to simulate a control system's environment in real-time. This is done to test the control system before it is used in its real environment. In this project, computer simulation of a certain kind of environments, called track-based systems, is studied and a general model for track-based systems is developed. In this model, track layouts are represented by graphs, which is a flexible and extensible representation and a method for visualizing these layouts is presented.

Typically, when Faurecia in Torsås are planning a new assembly line, one of the steps is to build a full-scale model of the line in card board, a form of mock-up planning. Faurecia has shown interest in finding an alternative methodology. The purpose was to explore the possibility of replacing today's cardboard based mock-up planning with models in a digital simulation environment.The purpose of the thesis has been to answer some of these complex questions; What are the benefits of using a simulation tool? In what way can we use it? If we choose to use a simulation tool, in what way does it affect our way of planning an assembly line? What are the advantages and disadvantages? Are there any economical and social aspects?Our results made us realize that a digital simulation tool does not replace the card board. On the other hand simulation could be used as a complement.

This thesis of 15 hp has been implemented at Halmstad University, in collaboration with Saab Dynamics in Linköping. Saab Dynamics is a company operating in the defence industry where competition is tough. This necessitates new ways to increase efficiency in the company, which is the basis for this thesis. Saab Dynamics wants to introduce simulation driven design. Since Saab Dynamics engineers have little experience of simulation, required a user methodology with clear guidelines.

This thesis of 15 hp has been implemented at Halmstad University, in collaboration with Saab Dynamics in Linköping. Saab Dynamics is a company operating in the defence industry where competition is tough. This necessitates new ways to increase efficiency in the company, which is the basis for this thesis. Saab Dynamics wants to introduce simulation driven design. Since Saab Dynamics engineers have little experience of simulation, required a user methodology with clear guidelines.

ABB is one of the world?s leading engineering companies in power and automation technologiesand their solutions improve performance while lowering environmental impacts for energycompanies and industries. ABB FACTS designs equipment and plants for series and phasecompensation.This thesis has been performed at ABB FACTS on the Mechanical Design (DM) department inVästerås, Sweden. The purpose of the thesis was to develop and design calculations andsimulation tools for ABB FACTS?s standard series capacitor platforms.

This thesis of 15 hp has been implemented at Halmstad University, incollaboration with Saab Dynamics in Linköping. Saab Dynamics is a companyoperating in the defence industry where competition is tough. This necessitatesnew ways to increase efficiency in the company, which is the basis for this thesis.Saab Dynamics wants to introduce simulation driven design. Since SaabDynamics engineers have little experience of simulation, required a usermethodology with clear guidelines. Due to lack of time, they chose to assign thetask to students, which resulted in this thesis.The aim of the thesis is to develop a methodology in mechanical design, wherethe designer uses the FE analysis early in the design process to develop thestructures' mechanical properties.

This thesis of 15 hp has been implemented at Halmstad University, in collaboration with Saab Dynamics in Linköping. Saab Dynamics is a company operating in the defence industry where competition is tough. This necessitates new ways to increase efficiency in the company, which is the basis for this thesis. Saab Dynamics wants to introduce simulation driven design. Since Saab Dynamics engineers have little experience of simulation, required a user methodology with clear guidelines.

This study examines the use of building modeling and energy simulations in the design process  of  a  building.  The  take-off  point  is  the  notion  of  energy  simulations  being needed early and throughout the building design process, and that the lack of energy simulations may be explained by the fact that they are time consuming and therefore often too expensive. A greater interoperability between software tools used by relevant disciplines,  such  as  the  architect  and  the  energy  specialist,  would  create  smoother workflows, which would reduce this cost and open up for more frequent and iterative energy  simulation  processes.  The  study  is  an  assessment  of  the  modeling  tool  Revit and  the  simulation  tool  Virtual  Environment  and  whether  they  can  create  smoother workflows, and make leeway for a more frequent use of energy simulations throughout the  design  process.  It  also  investigates  the  limitations  of  what  can  be  examined  by simulations in Virtual Environment. This will hopefully help clarify the future role of energy  simulations  in  design  processes.  The  method  is  a  trial  by  error  approach  of testing the two software tools by building and simulating a model. The results of these tests  show  that  the  workflow  is  not  optimal  (and  therefore  time  consuming)  for frequent  and  iterative simulations  throughout the  design  process,  but  it  also  reveals some  great  possibilities  of  what  can  be  performed  with  these  two  powerful  tools  at hand.  Further  development  with  regards  on  platform  independency  of  the  building information  model,  including  seamless  exporting  and  importing,  seems  necessary  to strengthen the future role of energy simulations..

To enable the enhancement of the driver's environment in a forklift, an alternative form of steering has been evaluated. An earlier concept with a combined driving and steering wheel has been exchanged to a concept with two driving wheels. A link wheel has replaced the combined driving and steering wheel. The steering is done through differentiation of the velocities of the two driving wheels. The scope of this master thesis is to create a simulation model, create a control program and to evaluate the concept of two driving wheels.

For research purposes Saab has developed a generic mathematical model denoted VEGAS of an aircraft with a configuration similar to JAS 39 Gripen. Today parts of Gripen backup control system are used also for VEGAS making the system subject to both corporate and defense secrecy. The main objective of this master thesis is to design, verify and implement public pitch axis flight control system for VEGAS. Furthermore, simplifications regarding the design process is to be examined. Design of pitch axis flight control system for the entire flight envelope has been carried out.

This thesis of 15 hp has been implemented at Halmstad University, in collaboration with Saab Dynamics in Linköping. Saab Dynamics is a company operating in the defence industry where competition is tough. This necessitates new ways to increase efficiency in the company, which is the basis for this thesis. Saab Dynamics wants to introduce simulation driven design. Since Saab Dynamics engineers have little experience of simulation, required a user methodology with clear guidelines.

This thesis of 15 hp has been implemented at Halmstad University, in collaboration with Saab Dynamics in Linköping. Saab Dynamics is a company operating in the defence industry where competition is tough. This necessitates new ways to increase efficiency in the company, which is the basis for this thesis. Saab Dynamics wants to introduce simulation driven design. Since Saab Dynamics engineers have little experience of simulation, required a user methodology with clear guidelines.

This thesis of 15 hp has been implemented at Halmstad University, incollaboration with Saab Dynamics in Linköping. Saab Dynamics is a companyoperating in the defence industry where competition is tough. This necessitatesnew ways to increase efficiency in the company, which is the basis for this thesis.Saab Dynamics wants to introduce simulation driven design. Since SaabDynamics engineers have little experience of simulation, required a usermethodology with clear guidelines. Due to lack of time, they chose to assign thetask to students, which resulted in this thesis.The aim of the thesis is to develop a methodology in mechanical design, wherethe designer uses the FE analysis early in the design process to develop thestructures' mechanical properties.